4x4moose Posted January 8, 2007 Share Posted January 8, 2007 i need a braker bar so i can remove my main pully so i can take off my oil pump, anyone have one that i could use for a few minutes? i tried a rachet and a peice of pipe but it just kind of bent and broke the pipe. anybody got any other tricks? i havce a tourque wrench but i have always been told not to use it as a breaker bar but its the only thing that is long enough (i'm trying to use my starter to brake the bolt loose, some of you know what i'm talking about). Link to comment Share on other sites More sharing options...
eggroller Posted January 8, 2007 Share Posted January 8, 2007 i need a braker bar so i can remove my main pully so i can take off my oil pump, anyone have one that i could use for a few minutes? i tried a rachet and a peice of pipe but it just kind of bent and broke the pipe. anybody got any other tricks? i havce a tourque wrench but i have always been told not to use it as a breaker bar but its the only thing that is long enough (i'm trying to use my starter to brake the bolt loose, some of you know what i'm talking about).I used a pipe from Home Depot to break mine loose. I also had a buddy hold the brake pedal down as well leave the car in gear. Those combined together make short work of the bolt. I tightened it back the same way. The pipe is a heavy pipe about 2.5 feet long. I have used it to tighten the axle castle nut with my 18" Craftsman breaker bar. So, it gives you an idea of how heavy it is. Good luck! Link to comment Share on other sites More sharing options...
4x4moose Posted January 8, 2007 Author Share Posted January 8, 2007 yeah that was my next step, go to are ************y rump roast ace hardware. and a possilbe wet bike ride. Link to comment Share on other sites More sharing options...
eggroller Posted January 8, 2007 Share Posted January 8, 2007 yeah that was my next step, go to are ************y rump roast ace hardware. and a possilbe wet bike ride.Bummer I am helping a buddy with his car tonight. I could have rolled out there and helped you out. Link to comment Share on other sites More sharing options...
Turbone Posted January 9, 2007 Share Posted January 9, 2007 Use a 1/2in drive ratchet and pipe, make sure the pipe is at least 2.5ft long. Then lay it against the right side, usually against the battery(EA82). Remove the coil wire and give the ignition a quick bump. This will break the nut loose. Link to comment Share on other sites More sharing options...
4x4moose Posted January 9, 2007 Author Share Posted January 9, 2007 would that be drivers right on the ea-82? i've have tried it on both side and it didn't loosen it Link to comment Share on other sites More sharing options...
Turbone Posted January 9, 2007 Share Posted January 9, 2007 Yes, the drivers side. If you tried it on the other side, the wrench should have flipped over and caused noise/dents/broken windows, etc. Link to comment Share on other sites More sharing options...
4x4moose Posted January 9, 2007 Author Share Posted January 9, 2007 i have no idea why its not working i've done it before to replace a front manin seal. but i think i put the end of the pipe on diver's left and i used a real braker bar. Link to comment Share on other sites More sharing options...
Prospeeder Posted January 9, 2007 Share Posted January 9, 2007 i used a 4 foot long pipe to do mine, it ruined my 1/2 in drive ratchet tho, destroyed the ratcheting mechinism, so i returned it to sears and got another one for free, lol. left it in gear with the Ebrake on Link to comment Share on other sites More sharing options...
4x4moose Posted January 10, 2007 Author Share Posted January 10, 2007 so if you are stanign in front of the motor (ea-81) witch way does it spin? Link to comment Share on other sites More sharing options...
slideshow86 Posted January 11, 2007 Share Posted January 11, 2007 you know righty tighty lefty loosy? I really agree with the whole dropping of the coil wire and giving ignition a bump works every time. or if you have no ac just drop the rad and hit it with a 3/4 impact. Ive done both. Link to comment Share on other sites More sharing options...
daeron Posted January 11, 2007 Share Posted January 11, 2007 I infinitely prefer to use the rope trick, and some heavy pipe. rope trick: take a sprak plug out, slowly push a bit of rope into the cylinder, and then just turn it counter clockwise. You really have no idea how much force you can exert when youre laying on your back.. multiply that times a four foot bar and you are in business. If I'm using a piece of skinny or weak pipe as a cheater bar, I often get a piece of concrete rebar and put it in the other end of the pipe, making sure to overlap the rather/breaker bar handle and the rebar if possible. This stiffens the cheap pipe and helps keep it from bending. I dont think I have EVER had to resort to the starter bump to remove a crankshaft bolt, and not failed at that as well. The only time I can remember trying it, the crankshaft/timing sprocket/woodruff key on the engine in question had all been loctited together as a fix for a terminal engine problem... and it took a 3/4" impact gun being supplied by 5/8" air line to get that bugger loose. i am imagining somewhere on the order of 800+ pounds of force (not torque, not ft-lbs, pounds) to break that sucker loose. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now