xoomer Posted February 25, 2007 Share Posted February 25, 2007 Ok, I'm not sure if I have my distributor in right. Where on the flywheel am I supposed to drop it? The three lines? like the ea82? or somewhere else? and at the begining or the end of the cycle? Link to comment Share on other sites More sharing options...
daeron Posted February 25, 2007 Share Posted February 25, 2007 this is the forum for the ea82 cars.. I presume you are talking about the disty on your legacy. wrong forum :-p Link to comment Share on other sites More sharing options...
xoomer Posted February 25, 2007 Author Share Posted February 25, 2007 My 81 wagon has always been welcome here? (atleast I always thought It was?) Legacy's have coil packs!! Link to comment Share on other sites More sharing options...
daeron Posted February 25, 2007 Share Posted February 25, 2007 i didnt wanna sound unwelcome-ful.. thats why I stuck the dancing banana in there hey you know, oops. I glanced up at your user "staff" and checked vehicles, saw the legacy, and somehow presumed you werent talking about the wagon.. For that matter, which vehicle were you talking about, because now I am confused... I just jumped the gun and assumed it was a case of someone mistakenly posting a question about a 90 legacy in the "older gen" forum. I only made a point so that the thread would get moved to where you would get more help, I dont wanna be a nag :-\ Link to comment Share on other sites More sharing options...
[HTi]Dain Posted February 25, 2007 Share Posted February 25, 2007 Yes, for that case it must be important to clearly state what vehicle a person is talking about when making a post/thread. eh? Link to comment Share on other sites More sharing options...
TomRhere Posted February 25, 2007 Share Posted February 25, 2007 Ok, I'm not sure if I have my distributor in right. Where on the flywheel am I supposed to drop it? The three lines? like the ea82? or somewhere else? and at the begining or the end of the cycle? Pull #1 spark plug, put finger over plug hole and turn engine by hand until you feel pressure on your finger. Remove finger from plug hole and continue turning engine until the 0* mark is aligned with timing pointer. #1 plug tower on disty cap is the one nearest the rear hold-down clip. You want the disty rotor close to that area. The rotor will turn slightly as the drive gears mesh. You may need to re-pull disty to adjust how it finally aligns with cap tower. Link to comment Share on other sites More sharing options...
Phizinza Posted February 25, 2007 Share Posted February 25, 2007 Pull #1 spark plug, put finger over plug hole and turn engine by hand until you feel pressure on your finger. Remove finger from plug hole and continue turning engine until the 0* mark is aligned with timing pointer. #1 plug tower on disty cap is the one nearest the rear hold-down clip. You want the disty rotor close to that area. The rotor will turn slightly as the drive gears mesh. You may need to re-pull disty to adjust how it finally aligns with cap tower. +1, Thats what I was about to type. I've done this to many times.. But now it's time for ej power in my brat! Link to comment Share on other sites More sharing options...
Frank B Posted February 25, 2007 Share Posted February 25, 2007 The reason you put your finger over the plug hole to feel compression is to make sure your not on the exhaust stroke. If you skip that and just get the rotor lined up with #1 terminal, and the timing mark at 0, you could have the disty 180 degrees out. Link to comment Share on other sites More sharing options...
Gloyale Posted February 25, 2007 Share Posted February 25, 2007 line up the dot on the disty shaft with the little notch in the housing for a more excact no.1 line up.(from FSM) This compensates for the little twist and gets it in the right range for timing adjustment. you won't have a problem Link to comment Share on other sites More sharing options...
4x4_Welder Posted February 25, 2007 Share Posted February 25, 2007 As far as timing marks, unless you have an EA82 flywheel, there should be a set of lines, one marked 0º on the flywheel. If you want, I'll show you that on my hatch when you come over. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now