Meeky Moose Posted November 25, 2003 Share Posted November 25, 2003 got a littel red light that says ECS. it lit up yesterday after i changed a coolant hose that sprung a leak.. car is sorta hard to start now also.. gotta acctually give it pedal to get it to start sometimes.. Edit: this is the 85' RX ea82T i also noticed the tach started jumpin when this light came on.. think the disty might be goin bad? Link to comment Share on other sites More sharing options...
subarubrat Posted November 25, 2003 Share Posted November 25, 2003 You probably unplugged or loosened a connection from the ECS to the engine ECS is the ECU. Link to comment Share on other sites More sharing options...
Meeky Moose Posted November 25, 2003 Author Share Posted November 25, 2003 doh.. the hose i had to replace was just the one that goes from the intake to the turbo.. had to remove the turbo heat shield, but that was it.. nothing right there in the terms of wires to bump... if i have the codes read, it should tell me whats wrong, if its not a connection problem shouldn't it? Link to comment Share on other sites More sharing options...
subarubrat Posted November 25, 2003 Share Posted November 25, 2003 Try simply unplugging the ECU if it is carbed. My EA81 in the BRAT had driveability problems from the ECU triggering functions on the carb. I unplugged the ECU and it ran just fine and got better gas mileage. Link to comment Share on other sites More sharing options...
oddcomp Posted November 25, 2003 Share Posted November 25, 2003 umm since his is turbo i assume its fuel injected .. if you unplug the computer then you have nothing running the injectors ... and i would bet he has a leak somewhere in between the engine and the maf sensor causing it to start hard loose clamp the occasionally forgotten to re attach vacum line <i always hate those> ect ect Link to comment Share on other sites More sharing options...
Qman Posted November 26, 2003 Share Posted November 26, 2003 My guess would be that you either cracked one of the thermal switches or a vacuum line. Everything is probably getting a little hard and brittle. Check all the connections and vacuum lines as described above as well. Link to comment Share on other sites More sharing options...
Stupidru Posted November 26, 2003 Share Posted November 26, 2003 read the ecs code...it might be a o2 sensor....the o2 sensor is below the turbo heat shield. Link to comment Share on other sites More sharing options...
Dennis ex24 Posted November 26, 2003 Share Posted November 26, 2003 tony... ive always had to crack the throttle to get that car to start from day one. back in the early subaru turbo days there was a TSB out about this if im not mistaken...i have to do the same on my XT. a new fuel pressure regulator may/may not fix this - who knows. re: the jumpy tach - this wasnt a disty issue. i think it was just some little annoying voltage thing...youll notice when it starts jumping around a bit, if you were to turn on the headlights or some other big electrical thing on the car it'll either calm down or stop completely...another external ground will probably prevent this from happening again. Link to comment Share on other sites More sharing options...
Meeky Moose Posted November 27, 2003 Author Share Posted November 27, 2003 ok Dennis, the tach seemd to have fixed itself after i regrounded the car again.. used my ground wire off the wagon (it was beefy) on another note, what do i need to read the ecs code?? never messed with them before.. i'm assuming the little black box under the steering column is the computer.. its got a red light that flashes 3 long and 3 short per cycle.. any ideas? never had to crack the throttle at all on my 86' turbo wagon, and its got 290k on it. lol at any rate, maybe i'll pull the FPR off it and see what it does.. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now