SubaruJawn Posted October 18, 2007 Share Posted October 18, 2007 Hey Fellow Subaru Fanatics. i'm trying to put an ER27 in my Loyale. but how do i do the wiring. any know how to do the wiring? Subex also i tried to get ahold of the guy with the Yellow ER27 Link to comment Share on other sites More sharing options...
idosubaru Posted October 18, 2007 Share Posted October 18, 2007 hey J, are you wanting to create your own harness or use the one from the XT6 in your loyale? what exactly are you wanting to know? it's kind of a...get in there and do it type thing. keep what you need, cut away what you don't, fabricate the rest. it's really hard to give directions on something like this, more specific questions might help. Link to comment Share on other sites More sharing options...
SubaruJawn Posted October 18, 2007 Author Share Posted October 18, 2007 i ment does anyone have a diagram on the engine wiring. but if i can use xt6 wiring thats better Link to comment Share on other sites More sharing options...
idosubaru Posted October 18, 2007 Share Posted October 18, 2007 i would remove the XT6 engine wiring harness. you don't really want to use the loyale harness i wouldn't think. i say that...eventhough i've ran an XT with and XT6 ECU...so they are somewhat similar, but it sounds like it could get messy. you'll need to spend some solid hours looking over loyale and xt6 wiring diagrams to see if that's really feasible and worth it. the more straight forward way is to just use all XT6 stuff in the loyale. with the engine, harness, and ECU out of the XT6, plug everything up. then start stripping the wires you don't need. you'll probably have a few wires you're not sure about, check those against the wiring diagram and ask here. once it's ready, drop it all in the loyale. we have the XT FSM's posted at the xt site. you will want all the wiring diagrams, it's a bit of a mess. Link to comment Share on other sites More sharing options...
SubaruJawn Posted October 18, 2007 Author Share Posted October 18, 2007 well i got to do something to give my loyale more power. since i'm going to do it. i want to make sure i wont want to do something different. Example: if i pur in a ej22 then later want to put in a ER27. so may as well put ER27 in instead. and when get all that done yes i'll make sure i come here for more help. or on XT6.net Link to comment Share on other sites More sharing options...
idosubaru Posted October 18, 2007 Share Posted October 18, 2007 an EJ22 is the better motor choice by far. i understand you may have more XT6 parts, but for all that effort i would swap in an EJ22. that's a huge project and a lot of time and effort, i'd go ahead and make the extra effort for an EJ22. it's been done far more too, so you'd get more info from here. Link to comment Share on other sites More sharing options...
SubaruJawn Posted October 18, 2007 Author Share Posted October 18, 2007 well knowing that. makes wanna go after the ER27 even more. Link to comment Share on other sites More sharing options...
mikeshoup Posted October 18, 2007 Share Posted October 18, 2007 Pull the entire ER27 engine harness. Unfortunately, this harness is extremely long as it goes from the ECU in the trunk to the motor. You will want to cut this down. Here's a copy of the pages from the FSM for the 88XT engine diagrams. Both the ER27 MPFI and the EA82 MPFI. Make sure you look at the correct diagram. http://mshoup.us/docs/XT%20EA82%20MPFI%20ER27%20MPFI,%20Engine%20Wiring%20Diagram.pdf You're going to want to pull the whole engine wiring harness from the XT6. Then proceed to cut it down and remove unnecessary components from the harness. Unfortunately with harnesses from the XT, you'll also want to cut down the length as there is going to be many many extra feet since the computer is in the trunk. Too bad you're not in Colorado. I'd be totally up to helping you with the wiring. I'm great with electrical. Just not so great with the mechanical part. Link to comment Share on other sites More sharing options...
SubaruJawn Posted October 18, 2007 Author Share Posted October 18, 2007 i should bring both cars and visit you to get all this done. or just bring all i need. and the loyale. i'm ok with mechanical. and i'm horrible with electronics Link to comment Share on other sites More sharing options...
WoodsWagon Posted October 19, 2007 Share Posted October 19, 2007 If you want to go different, go with an EZ30. More displacement, more power, more torque, timing chains instead of belts, and more importantly, shorter. As in may-actually-fit-in-engine-bay shorter. Unlike the ER27, which had to have the nose of the xt redesigned to fit around it. Same with the EG33, it's just too long of an engine to fit. The EZ30 was designed to fit in the 4cyl engine bay however, so it's a lot closer to fitting than anything else. Link to comment Share on other sites More sharing options...
Numbchux Posted October 19, 2007 Share Posted October 19, 2007 an ER27 swap is similar power to an EJ22. but much more work (physically bigger engine), and still has the crappy 2 tbelts that make the EA82 a POS. Link to comment Share on other sites More sharing options...
SubaruJawn Posted October 19, 2007 Author Share Posted October 19, 2007 i need the more weight. to make her heavier. i'd love to put in an EZ30 but i dont got that kinda money. and i dont know what i'd have to do to make it work. a 6 cylinder designed to fit in 4 cylinder bay. sounds very nice. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now