Dynapar Posted March 16, 2008 Share Posted March 16, 2008 I was pulling the rear end out of the brat tonight and I ran into a snag. I cannot get either of the rear axles off of the rear diff. I tried pulling the axles out of the hubs but the stubs are too long and I dont have enough room to play around with. I am very unfamilar with the older subarus. Perhaps there is something that I am over looking? So does anyone have any secret methods to getting the axles off of the stubs on the diff? I already have the roll pins out. I would prefer to not use heat cause I dont want to fry the diff fluid. Also I have blasted it with penetrating oil to no avail. Link to comment Share on other sites More sharing options...
1bignose Posted March 16, 2008 Share Posted March 16, 2008 two thing first thing to make life ez drop the diff you cant pull them all the way off less you do at lease i cant sec thing is if you cant move the shaft then go get a can of k&n air filter oil spray it on and let it sit for an hour and it should slide off if not tap the shaft with a dead blow hammer hope it helped dennis Link to comment Share on other sites More sharing options...
TomRhere Posted March 16, 2008 Share Posted March 16, 2008 The axles have rusted to the splines. Heat, penetrating spray and hammer is the method called for. Heat the spline area, spray with the penetrant, repeat. That'll help draw the penetrant into the splines, but you may have to let them soak for a bit, like a day or two. Then you start beating the crap out of them. Once you get them off, clean the splines real good and apply some Anti-Sieze to them. I get to do this to all 3 of my BRATs here shortly....:-\ Link to comment Share on other sites More sharing options...
Qman Posted March 16, 2008 Share Posted March 16, 2008 Silly question but... did you take the roll pins out? Link to comment Share on other sites More sharing options...
Numbchux Posted March 16, 2008 Share Posted March 16, 2008 Silly question but... did you take the roll pins out? I already have the roll pins out don't need to drop the diff to get them out. but you'll probably have to unbolt the shock, and pull the trailing arm down to give some slack to get them off the stub.... Link to comment Share on other sites More sharing options...
Dynapar Posted March 16, 2008 Author Share Posted March 16, 2008 Got one of the axles off. So now the diff is on floor with the passenger axle still attached. I was BFH-ing the passenger axle and well I cracked teh DOJ cup and dislocated the joint. The thing wont budge at all! Tomorrow I am moving up to larger implements of destruction. It sucks my camera is broken or else I would have a bunch of pics to post up. Link to comment Share on other sites More sharing options...
[HTi]Johnson Posted March 16, 2008 Share Posted March 16, 2008 ...I am moving up to larger implements of destruction. That just made my day:headbang:. Pretty funny. Sorry to hear the it isn't working out. Link to comment Share on other sites More sharing options...
Qman Posted March 17, 2008 Share Posted March 17, 2008 don't need to drop the diff to get them out. but you'll probably have to unbolt the shock, and pull the trailing arm down to give some slack to get them off the stub.... Thx, sorry, I missed that... Link to comment Share on other sites More sharing options...
Numbchux Posted March 17, 2008 Share Posted March 17, 2008 Thx, sorry, I missed that... it happens I got your message....but I was at work. I can't believe you cracked the DOJ cup! that's crazy. I've beat on, and deformed them, even cut one off one of the spindles that was in the XT control arms I got. Link to comment Share on other sites More sharing options...
idosubaru Posted March 17, 2008 Share Posted March 17, 2008 I was BFH-ing the passenger axle and well I cracked teh DOJ cupbeen there, done that. never got them off either - went to the scrap yard, diff and all. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now