stavan Posted August 19, 2008 Share Posted August 19, 2008 Subaru Legacy 1990 The vent system (cabin fresh air supply) usually works well. But sometimes when I push the “Vent” button I hear a sound of a vent somewhere but NO air comes out of the grilles. If I drive for a while with the “Vent” button on (green on the attached photo) at some point air starts blowing out of the grilles. What could be the reason? How can I repair it? Thanks. Link to comment Share on other sites More sharing options...
Legacy777 Posted August 19, 2008 Share Posted August 19, 2008 Problem & fix can be found here http://bbs.legacycentral.org/viewtopic.php?t=1142 Link to comment Share on other sites More sharing options...
EVOthis Posted August 19, 2008 Share Posted August 19, 2008 Legacy777..im not sure about the motor differences between the 1st gen and second gen....but in the article are they talking about the mode door motor? the little black plastic box on the drivers side.... Link to comment Share on other sites More sharing options...
Legacy777 Posted August 19, 2008 Share Posted August 19, 2008 Yes I believe that is what they are referring to by the mode door motor Link to comment Share on other sites More sharing options...
EVOthis Posted August 19, 2008 Share Posted August 19, 2008 thanks Legacy777 i will tinker with her a bit... Link to comment Share on other sites More sharing options...
stavan Posted August 24, 2008 Author Share Posted August 24, 2008 Subaru Legacy 1990The vent system (cabin fresh air supply) usually works well. But sometimes when I push the “Vent” button I hear a sound of a vent somewhere but NO air comes out of the grilles. If I drive for a while with the “Vent” button on (green on the attached photo) at some point air starts blowing out of the grilles. What could be the reason? How can I repair it? Thanks. Thanks for the links. One more thing: How do I take out the AC control panel? - see picture Is it bolted somehow...? It doesn't move when I try by hand. Link to comment Share on other sites More sharing options...
stavan Posted September 2, 2008 Author Share Posted September 2, 2008 I am still trying to figure out where that "heater door cable" is located. Is it in the engine compartment or inside (in the cabin) under the plastic claddings...? I will appreciate if you could refer to a photo or some good description of location of that heater door cable. Thanks, Stan Link to comment Share on other sites More sharing options...
stavan Posted September 5, 2008 Author Share Posted September 5, 2008 Well, I took out the stereo and I could barely touch the cable but there is no way to get the unit our without disconnecting it. And there is no way to disconnect that cable without dismounting all the plastic cladding under dashboard… Stan:mad: Link to comment Share on other sites More sharing options...
McDave Posted September 5, 2008 Share Posted September 5, 2008 Edit: nevermind. Link to comment Share on other sites More sharing options...
Legacy777 Posted September 5, 2008 Share Posted September 5, 2008 He was trying to get the cable out to get the heater control unit out. It's definitely the control unit. The solder joints are a common failure point. Stan, I'll see if I can find any info in the manuals regarding getting that heater control unit out. From what I remember, the cable shouldn't be limiting you getting it out. Did you take the stereo out? There may be screws just above it. I don't recall exactly. Josh Link to comment Share on other sites More sharing options...
McDave Posted September 5, 2008 Share Posted September 5, 2008 He was trying to get the cable out to get the heater control unit out. It's definitely the control unit. The solder joints are a common failure point. Doh! Must drink caffeine before posting! Post edited. Link to comment Share on other sites More sharing options...
stavan Posted September 6, 2008 Author Share Posted September 6, 2008 Stan, I'll see if I can find any info in the manuals regarding getting that heater control unit out. From what I remember, the cable shouldn't be limiting you getting it out. Did you take the stereo out? There may be screws just above it. I don't recall exactly. Josh Hi Josh, Yes there are screws underneath the unit. I got the unit loose and the cable is the only thing that is dragging the unit. Now I have to figure out how to access one of the ends of the cable preferably without taking out all the plastics under dashboard... As a matter of fact all the buttons are working right now but if I go the lazy way and put it back it might not work just when I need it in the cold rain... Stan Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now