Hocrest Posted January 7, 2004 Share Posted January 7, 2004 I was talking to a friend of mine that has a OB wagon, I think it is a 99. He has about 60-70K miles on it. His speedo/odometer isn't working. As far as I know, that is the only problem. My first thought was one of the speed sensors, but wouldn't that affect shifting or throw on a CEL. I haven't seen the car, and he lives a couple of hours away. For now I'm just looking for some diagnostic help/ideas to throw his way. Thanks Link to comment Share on other sites More sharing options...
99obw Posted January 7, 2004 Share Posted January 7, 2004 http://usmb.ultimatesubaru.org/forum/showthread.php?s=&threadid=7590& Link to comment Share on other sites More sharing options...
Guest jclay Posted January 13, 2004 Share Posted January 13, 2004 The speedometer on my '94 legacy crapped out; somehow the cable became loose from the speedometer itself. Try using a mirror to see undrneath the steering column ( unless you are a contortionist its hard to do otherwise) If thats the case, have one person hold it in place where it meets the tranny or adaptor or whatever, while the other person reconnects underneath the dash. also, i don't know about that particular model, but some earlier legacies have an adaptor thingy (between the cable and trans.)that can apparently crap out also, but i'd check the cable first. Does his odometer work? Link to comment Share on other sites More sharing options...
Legacy777 Posted January 13, 2004 Share Posted January 13, 2004 this is the adapter base that goes out http://www.main.experiencetherave.com:8080/subaru/images/speedocablebase.jpg Link to comment Share on other sites More sharing options...
urabus1995 Posted December 18, 2009 Share Posted December 18, 2009 this is the adapter base that goes out http://www.main.experiencetherave.com:8080/subaru/images/speedocablebase.jpg Hi Again, Does this give a CEL and cause the car to cut out on low revs? Link to comment Share on other sites More sharing options...
Scooby17 Posted December 18, 2009 Share Posted December 18, 2009 When the speed sensor was out on 98 legacy it threw code P0420 I think. ECU went to limp mode and no revving over about 4000 rpm (ecu would cut engine out then would work again after a few seconds). Revving in lower rpms was fine though. Link to comment Share on other sites More sharing options...
johnceggleston Posted December 18, 2009 Share Posted December 18, 2009 I was talking to a friend of mine that has a OB wagon, I think it is a 99. He has about 60-70K miles on it. His speedo/odometer isn't working. As far as I know, that is the only problem. My first thought was one of the speed sensors, but wouldn't that affect shifting or throw on a CEL. I haven't seen the car, and he lives a couple of hours away. For now I'm just looking for some diagnostic help/ideas to throw his way. Thanks bad speedos are a fairly common problem for the 99 year, outbacks anyway. in most other years i would guess the speed sensor end of things, but for a 99 it's probably the speedo. do a search and you should find several threads on this. you can use a speedo out of any 96 - 98 (99) outback, at least. maybe 00- beyond. Link to comment Share on other sites More sharing options...
themoneypit Posted September 20, 2010 Share Posted September 20, 2010 bad speedos are a fairly common problem for the 99 year, outbacks anyway. in most other years i would guess the speed sensor end of things, but for a 99 it's probably the speedo. do a search and you should find several threads on this. you can use a speedo out of any 96 - 98 (99) outback, at least. maybe 00- beyond. i dont think this is true... i bought a cluster from a 98 and it wouldnt work.. i believe they have a 2 wire speedo plug, the 99 has a one wire plug.. all the other guages etc worked, but no speedo... Link to comment Share on other sites More sharing options...
logic23 Posted September 21, 2010 Share Posted September 21, 2010 yep the 99 spedo is a one year only.... the issue is a bad chip or loose connection on the board...new spedo=dealer only=expensive. I drive my 99 using the tach.. Link to comment Share on other sites More sharing options...
idosubaru Posted September 21, 2010 Share Posted September 21, 2010 dave - the 99 is a specific known issue of that year only. Link to comment Share on other sites More sharing options...
edrach Posted September 21, 2010 Share Posted September 21, 2010 When the speed sensor was out on 98 legacy it threw code P0420 I think.ECU went to limp mode and no revving over about 4000 rpm (ecu would cut engine out then would work again after a few seconds). Revving in lower rpms was fine though. P0420 is an emissions related code; that code shouldn't cause you to go into limp mode. Check the code again. Link to comment Share on other sites More sharing options...
daredevil1166 Posted September 21, 2010 Share Posted September 21, 2010 i dont think this is true... i bought a cluster from a 98 and it wouldnt work.. i believe they have a 2 wire speedo plug, the 99 has a one wire plug.. all the other guages etc worked, but no speedo... Interesting.....I have a cluster from a 96-98 Outback in my 99 Outback. Link to comment Share on other sites More sharing options...
Gloyale Posted September 21, 2010 Share Posted September 21, 2010 Interesting.....I have a cluster from a 96-98 Outback in my 99 Outback. Yeah, I'm pretty sure they interchange. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now