mykingcrab Posted September 28, 2008 Share Posted September 28, 2008 (edited) Just got new timing set (complete kit) replaced. She has ran strong ,with all vital signs in excellent range until the timing components were replaced. Today,it was taking the mechanics family (not me)to church, and thanks to an observent driver (again not me),it was shut down and came home on a flatbed towtruck, in an effort to avoid any possable damage. According to the mech,he never let it get hot:) WHAT THE H__L? (1 ran ok at an idle. (2)dragged its butt up even a slight hill. (3) will not pull under a load. (4) TEMPATURE runs HOT. Also might consider that the old timing belt(s) tension was slopppppy. and the CTS+O2 SENSORS ARE BOTH NEW. This was a night and day issue.:confused::confused: HELP PLEASE !!!!!!!!!!!!! Edited October 1, 2008 by mykingcrab Link to comment Share on other sites More sharing options...
GeneralDisorder Posted September 28, 2008 Share Posted September 28, 2008 I would say the timing could be off a tooth. It will still run, just won't have any power. All the air bled from the cooling system? GD Link to comment Share on other sites More sharing options...
suberdave Posted September 28, 2008 Share Posted September 28, 2008 my guess is that the timing jumped a tooth. ide pull the front covers, and check it out... -=Suberdave=- Link to comment Share on other sites More sharing options...
mykingcrab Posted September 28, 2008 Author Share Posted September 28, 2008 I hav'nt talked to you guys in a while, and was in the process of threading some other mods(stay tuned) and this popped up. good leads. I left speculation out of the thread, I was hoping you guys would be thinking the same as me and COBCOB. I am courious????????? could there be an ignition timing issue????? or cam timing issue??????????? Link to comment Share on other sites More sharing options...
GeneralDisorder Posted September 28, 2008 Share Posted September 28, 2008 could there be an ignition timing issue?????or cam timing issue??????????? Absolutely - since the timing belt runs both the cams and the ignition. Redo the belts, then reset the distributor. GD Link to comment Share on other sites More sharing options...
Snowman Posted September 28, 2008 Share Posted September 28, 2008 One more vote for cam timing off a tooth. Doing the belts in the car, it's kinda hard to see the driver's side alignment marks. I've screwed it up before, and the car exhibited similar symptoms...idled okay but NO power. Mine even backfired pretty good. Link to comment Share on other sites More sharing options...
cobcob Posted September 30, 2008 Share Posted September 30, 2008 Mykingcrab's out of town at the moment so I stepped in as his proxy wrench... I got the RX over to my place yesterday to survey the situation. Correct on all accounts. DS belt was off a tooth so I re-did BOTH belts just to make certain. On this vehicle, due to the amount of lift, the marks are pretty easy to see if you're laying under the car looking up. The alternator blocks the view from on top which is annoying as heck though! She's running great now. Link to comment Share on other sites More sharing options...
mykingcrab Posted October 1, 2008 Author Share Posted October 1, 2008 (edited) GD, suberdave, CobCob and others. thanks once again. you guys nailed the problem again. CobCob dude thanx a million, was the distributer timing ok? :banana: you can drive her all week, NO jumping, Edited October 1, 2008 by mykingcrab Link to comment Share on other sites More sharing options...
cobcob Posted October 1, 2008 Share Posted October 1, 2008 Ign timing was OK... Just that slipped belt. I'm fixin to install my 5 tone air-horn into it tonight and then I'm hangin' out with Bo and Luke... Link to comment Share on other sites More sharing options...
mykingcrab Posted October 1, 2008 Author Share Posted October 1, 2008 Dude, your scaring me, remember we need to don this this spring. heres what we start with. http://www.jegs.com/instructions/555/rollcage.pdf Link to comment Share on other sites More sharing options...
cobcob Posted October 1, 2008 Share Posted October 1, 2008 how about a custom SS one of these?? Link to comment Share on other sites More sharing options...
mykingcrab Posted October 1, 2008 Author Share Posted October 1, 2008 l Picture you C.A.D. ing this up right now, and your crew water jetting/TIG'n and polishing as we speak:lol: Link to comment Share on other sites More sharing options...
SubPar Posted October 1, 2008 Share Posted October 1, 2008 I opened up this thread expecting to find a pictures of a Porsche 911 Turbo engine in an EA82. I'm so disappointed. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now