The Scooby Posted January 26, 2009 Author Share Posted January 26, 2009 ya it ends up the carbed feed is 5/16's, and the feed for the SPFI pump is 3/8'ths or so, i was able to get some more fittings today and get the pump in. Link to comment Share on other sites More sharing options...
Phizinza Posted January 28, 2009 Share Posted January 28, 2009 Just remember to use EFI rated hose on the feed and return lines. Would hate to see what a 40psi fuel pump can do spraying fuel all over your engine through the 8mm pipe Link to comment Share on other sites More sharing options...
The Scooby Posted January 28, 2009 Author Share Posted January 28, 2009 well im going to run all stock lines, many others have without any problems. but the feed line in the engine bay should be fine. i would like to remove the stock fuel lines and rerun new lines but i dont have time to do so. Link to comment Share on other sites More sharing options...
Phizinza Posted January 28, 2009 Share Posted January 28, 2009 I mean EFI rated rubber hoses. You might be ok with the smaller steel return line. But please don't use plain carby rated rubber hose! I've had a car light on fire (from battery problems) and it really isn't FUN! Link to comment Share on other sites More sharing options...
Pooparu Posted January 31, 2009 Share Posted January 31, 2009 It's not really that hard or time consuming. I went to the junk yard and pulled fuel lines for EFI Subarus and it didn't cost me anything, and it took me all of 5 to 10 minutes to replace all the rubber lines in the car. Any job worth doing is a job worth doing right. I know you might be eager to get your car going but cutting corners now will be much more costly and time consuming in the end. Trust me, take the time. Link to comment Share on other sites More sharing options...
mellow65 Posted January 31, 2009 Share Posted January 31, 2009 As long as you have a good friend who knows what they are doing. dude i still tell you, i had no idea what the hell i was doing. you just got lucky. Link to comment Share on other sites More sharing options...
Pooparu Posted January 31, 2009 Share Posted January 31, 2009 We'll call it smart luck on your part. Link to comment Share on other sites More sharing options...
oldschool Posted February 2, 2009 Share Posted February 2, 2009 Here is my first project car I did, 87 gl wagon Link to comment Share on other sites More sharing options...
SubaruJawn Posted February 8, 2009 Share Posted February 8, 2009 anyone post pix of were the wiring starts and ends on the legacy ? from engine to ECU (dash apart that is) i have manual that tells me how to take dash apart (most of the fear gone) knowing I've done some petty wiring gives me a little confidence. (door wiring) Link to comment Share on other sites More sharing options...
Pooparu Posted February 9, 2009 Share Posted February 9, 2009 It loops in and out of the legacy. Just start pulling everything out, and you'll have to get into the driver's side fender as well. I found it to be easier to just take it off. Sorry no pic of the carnage. Link to comment Share on other sites More sharing options...
kingbobdole Posted February 9, 2009 Share Posted February 9, 2009 Last dash I pulled took me about an hour to get out and I had to be nice (just doing a heater core) There are surprisingly few bolts holding it in... just get it out of the way. Link to comment Share on other sites More sharing options...
SubaruJawn Posted February 9, 2009 Share Posted February 9, 2009 (edited) It loops in and out of the legacy. Just start pulling everything out, and you'll have to get into the driver's side fender as well. I found it to be easier to just take it off. Sorry no pic of the carnage. ok. so it doesn't go threw the firewall ? (trying to build confidence on the swap) Last dash I pulled took me about an hour to get out and I had to be nice (just doing a heater core) There are surprisingly few bolts holding it in... just get it out of the way. ok don't see were the wires are at. P.S Will i have any problems with the exhaust fitting ? Edited February 9, 2009 by SubaruJawn Link to comment Share on other sites More sharing options...
Pooparu Posted February 9, 2009 Share Posted February 9, 2009 The wiring also goes through the fire wall near the heater core (I think it's just motor sensors). Link to comment Share on other sites More sharing options...
SubaruJawn Posted February 9, 2009 Share Posted February 9, 2009 ok. i believe I'm ready. so hype to do this Link to comment Share on other sites More sharing options...
Phizinza Posted February 10, 2009 Share Posted February 10, 2009 ok don't see were the wires are at. http://www.ultimatesubaru.org/forum/showthread.php?t=87000 Link to comment Share on other sites More sharing options...
86subieXT Posted December 10, 2011 Share Posted December 10, 2011 Hey, just read through this thread and have a few questions. sorry for bringing it back from the dead. I have an 88 XT 5 spd and want to put a EJ20t into it. Am i able to use the EA tranny? will it bolt up to the bell housing and crossmember? Link to comment Share on other sites More sharing options...
rpholz Posted December 10, 2011 Share Posted December 10, 2011 search function is handy.... that being said no. you have to use an adaptor plate with the ea flywheel redrilled to bolt on the ej. also up pipe may or may not clear the crossmember but i cant recall at the moment. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now