EvilDead Posted March 17, 2009 Share Posted March 17, 2009 Vehicles: 88 GL wagon disk brakes all around. 87 RX disk brakes all around. I have a leaky front passenger caliper on my RX. Know I know it is probably easier to just rebuild the sucker, but I'd rather just swap out the one from the wagon first being the parts store is over 30 minutes away. Now I got the caliper off the assembly, but I can't figure out how to get the darn cables off for the swap. It's currently hanging down from the car. Do I remove the entire assembly from the caliper, or just release the cable somehow? Thanks in advance for the help. Link to comment Share on other sites More sharing options...
Turbone Posted March 17, 2009 Share Posted March 17, 2009 Are you talking about the e-brake cable? If so, you need to pull the lever back a little bit so you have some slack and then use a pair of pliers and pull the end off the lever. Link to comment Share on other sites More sharing options...
Phizinza Posted March 17, 2009 Share Posted March 17, 2009 make sure your hand brake isn't on too... lol Link to comment Share on other sites More sharing options...
EvilDead Posted March 18, 2009 Author Share Posted March 18, 2009 Yeah it's the E-brake cable, unless there is another. Yeah I had the e-brake off, and I tried to grab it with a pliers, but it wouldn't budge! I guess I'll just try using more force, or a vice grip to pull it off. I just didn't want to start trying to pull on it harder if that wasn't the way it's supposed to go. Darn Chilton wasn't much help for my year brakes. Seems it skipped that step. Thanks for the replies fellas. Link to comment Share on other sites More sharing options...
TheCaptain Posted March 18, 2009 Share Posted March 18, 2009 If the rubber boot is on there try pulling it away from the lever to expose more cable, it helps sometime. good luck Link to comment Share on other sites More sharing options...
EvilDead Posted March 18, 2009 Author Share Posted March 18, 2009 Yeah everything is in good condition, and all the rubber boots are there. I just sprayed some PB blaster on the sucker, and I'll give it a go in the morn. I'll keep everyone posted!! Thanks again for the responses everyone. USMB rocks. Link to comment Share on other sites More sharing options...
Txakura Posted March 18, 2009 Share Posted March 18, 2009 "Darn Chilton wasn't much help". No kidding, I just did some work on my Jeep and Chilton's had such useful advice as 'if the axle seal is bad, replace it', 'if the axle bearing is excessively worn replace it with a new one' of course, how the frick you're supposed to get the seal and bearing out of the axle housing weren't worth mentioning... and unless you have x-ray vision, it's hard to inspect the bearing without pulling it - and even less likely it'll survive the removal with home tools! Carry on, just had to vent. And aren't those crappy black and white photos useful... ok, done now... really Link to comment Share on other sites More sharing options...
Phizinza Posted March 18, 2009 Share Posted March 18, 2009 Are you pulling on the cable? If so don't... Push the lever to the e-brake on position and then pull the cable while wriggling it and slot it out Link to comment Share on other sites More sharing options...
EvilDead Posted March 18, 2009 Author Share Posted March 18, 2009 I just pushed in the lever, and slid the cable end out. No need to pull on the cable and mess it up. So I got it all done! Works good, and even better after a final bleed. Is there a tool that twists the caliper so ya can compress, or line up to the brake pads? I had to twist it a little bit so the rivet on the outside of the inside brake pad would line through, and allowing for the caliper to slide into place. Other than that, had it done in no time. Ran all the fluid out too! Link to comment Share on other sites More sharing options...
Phizinza Posted March 19, 2009 Share Posted March 19, 2009 Mine normally get stuck in the lever thus need a little pull once the lever is pushed back Link to comment Share on other sites More sharing options...
EvilDead Posted March 19, 2009 Author Share Posted March 19, 2009 Mine normally get stuck in the lever thus need a little pull once the lever is pushed back Both came right out with ease. Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now