()__1337_CRAYOLA__()> Posted April 5, 2009 Share Posted April 5, 2009 i just did a re ring and head gaskets on my ea81 and im having hard starting now like it has really high compression and its hard turning over plus you have to feather the throtle to get it to fire but it runs and idles perfect after it is started what could this be? Link to comment Share on other sites More sharing options...
TomRhere Posted April 5, 2009 Share Posted April 5, 2009 1st guess would be ignition timing is to advanced. 2nd guess would be battery cable connections. 3rd guess would be weak starter. Link to comment Share on other sites More sharing options...
Cougar Posted April 5, 2009 Share Posted April 5, 2009 Very good suggestions from TomRhere. The only thing I can add to that is to see if the battery voltage is falling below 9 volts when trying to start the car. A weak battery or bad starter drawing too much current could cause that problem. Link to comment Share on other sites More sharing options...
()__1337_CRAYOLA__()> Posted April 5, 2009 Author Share Posted April 5, 2009 i guess the only funny thing is i never pull the distributor and the battery has good voltage as it is brand new so i guess ill still check the timming Link to comment Share on other sites More sharing options...
GeneralDisorder Posted April 5, 2009 Share Posted April 5, 2009 (edited) You installed new rings without honing the cylinders? (you couldn't have left the distributor in place unless you didn't split the block - thus it sounds like you installed rings without honing). Did you gap the rings or even pay attention to where the gaps were in relation to each other?? If that's the case it's probably hard to start because the rings will never seat and you have poor compression. GD Edited April 5, 2009 by GeneralDisorder Link to comment Share on other sites More sharing options...
Cougar Posted April 5, 2009 Share Posted April 5, 2009 i guess the only funny thing is i never pull the distributor and the battery has good voltage as it is brand new so i guess ill still check the timming Have you verified the voltage is ok? New batteries can still need a charge to get them to full capacity. Link to comment Share on other sites More sharing options...
XT6 Magic Posted April 5, 2009 Share Posted April 5, 2009 Since the cylinder pressure is up now because of the re-ring you may have to retard the timing slightly. If you are still using the SPFI you have to connect the green check connectors under the dash when you set the timing I think. Otherwise just try backing it off a little. Link to comment Share on other sites More sharing options...
()__1337_CRAYOLA__()> Posted April 5, 2009 Author Share Posted April 5, 2009 GD i did hone the cylinders without splitting the block i know it is redneck and i also payed attention to ring spacing and allignment but i had to get the engine running again in 1 day.... it took 15 hours to remove re-ring put headgaskets in and put it back in.. i didnt think anything of the other engine i bought untill i found it didnt have the power steering pump bolt holes which forced me to rering and put head gaskets in this one Link to comment Share on other sites More sharing options...
GeneralDisorder Posted April 6, 2009 Share Posted April 6, 2009 Why didn't you drill/tap the holes for the power steering pump? Anyway - without splitting the block some of your metal from honing is now inside the engine. That isn't real good for it. What type of hone did you use? What grit? And what angles? Have you done a compression check? New rings often are hard to start till they seat in. If you did the hone properly they should seat within a few thousand miles - unless you used chrome faced rings, in which case you may have to wait a lot longer. GD Link to comment Share on other sites More sharing options...
()__1337_CRAYOLA__()> Posted April 6, 2009 Author Share Posted April 6, 2009 i used standard napa rings i donno what they were.. no meat on the case to drill and tap from what i could tell the block i have actually has the casting for it i made sure to use wd40 while honing and then brake clean to rise as much as possible away.... then ran it 10 miles and changed the oil again now im running it 500 more miles then ill change the oil again Link to comment Share on other sites More sharing options...
()__1337_CRAYOLA__()> Posted April 6, 2009 Author Share Posted April 6, 2009 also what would cause low oil pressure after re-ring and head gaskets.... im not losing any oil any where.... i did clean all the carbon build up in the heads and block and there was alot so im lost on that to... Link to comment Share on other sites More sharing options...
()__1337_CRAYOLA__()> Posted April 7, 2009 Author Share Posted April 7, 2009 bumpo what would cause low oil pressure after all this? Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now