kmckinney0126 Posted April 30, 2009 Share Posted April 30, 2009 (edited) Okay so I have a 93 Legacy L 2wd with a little less than 200K that just died while I was coasting around a corner and now will not turn over. It will crank and crank but nothing. It sounds like a different crank to me as well. Like now it sounds"flat" compared to the way it sounded before when it would crank. I have checked for fuel and it is being delivered. I checked all the plug wires and they are intact and secure. I have not checked for spark, but it seems that a bad coil pack or other would not just go out while it was firing, I dunno. I do however have the cam sprocket covers off and have inspected the timing belt. The belt is intact on both sides and taught. I can see the marks on the cam sprockets but I'm not sure how to check if it is in time. Can someone please let me know how I can check to see if it jumped time or have any other ideas? Edited April 30, 2009 by kmckinney0126 add info Link to comment Share on other sites More sharing options...
OB99W Posted April 30, 2009 Share Posted April 30, 2009 [...]I can see the marks on the cam sprockets but I'm not sure how to check if it is in time. Can someone please let me know how I can check to see if it jumped time or have any other ideas? 2.2 Liter: http://endwrench.com/images/pdfs/2.2SingleOverWin01.pdf http://endwrench.com/images/pdfs/2.2Liter.pdf http://endwrench.com/images/pdfs/TBeltEWWin05.pdf Motor Magazine series; starts with 2.2, then moves on to 2.5: http://www.motor.com/magazine/pdfs/072001_08.pdf http://www.motor.com/magazine/pdfs/082001_08.pdf http://www.motor.com/magazine/pdfs/092001_08.pdf http://www.motor.com/magazine/pdfs/102001_08.pdf http://www.motor.com/magazine/pdfs/112001_08.pdf Be sure to use the lines (''hash marks'') on the sprockets, not the arrows, when checking the timing. Don't be concerned about the belt marks, as long as the sprocket marks are in the right relationship to each other. Link to comment Share on other sites More sharing options...
johnceggleston Posted April 30, 2009 Share Posted April 30, 2009 slightly off topic and maybe unnecessary: since you can't see the crank timing hash mark with the timing cover and crank pulley in place, maybe it would make sense, whenever you have one apart, to paint a 'timing' mark on the crank pulley, 180* away from the keyway so you could see it at a glance. just a thought. Link to comment Share on other sites More sharing options...
Olnick Posted May 1, 2009 Share Posted May 1, 2009 maybe it would make sense, whenever you have one apart, to paint a 'timing' mark on the crank pulley, 180* away from the keyway so you could see it at a glance. just a thought. Sounds like a very good idea, johnc. Could be very helpful in the right circumstances. Link to comment Share on other sites More sharing options...
kmckinney0126 Posted May 20, 2009 Author Share Posted May 20, 2009 Thanks so much for the links. They were paramount to getting my marks in time. She is running now but with some valve noise. HLA's may have bled down but still has that 2.2 get up. Once again thanks to the USMB for helping me get off the bus. Link to comment Share on other sites More sharing options...
GeneralDisorder Posted May 20, 2009 Share Posted May 20, 2009 I have seen water pump failure cause the belts to jump time. Inspect carefully to insure nothing is locking up and that the hydraulic tensioner is not defective. GD Link to comment Share on other sites More sharing options...
kmckinney0126 Posted May 20, 2009 Author Share Posted May 20, 2009 Procedure included oil seals on cams and crank, water pump, stat, t-belt, lower idler pulley and sprocket. Should have done the oil pump while I was there. I learned the hard way not to move the cams excessively as your HLA's may bleed down and you will have a whole other chore on your hands as I do. :mad: Link to comment Share on other sites More sharing options...
OB99W Posted May 20, 2009 Share Posted May 20, 2009 Thanks so much for the links. They were paramount to getting my marks in time. She is running now but with some valve noise. HLA's may have bled down but still has that 2.2 get up. Procedure included oil seals on cams and crank, water pump, stat, t-belt, lower idler pulley and sprocket. Should have done the oil pump while I was there. I learned the hard way not to move the cams excessively as your HLA's may bleed down and you will have a whole other chore on your hands as I do. :mad: You're welcome, I'm glad that the links helped. Yes, the screws on the oil pump back plate should be checked for tightness whenever the TB work is done. When they're loose, the oil diversion can cause both a crank seal leak and the HLAs to not pump up readily. Also see: http://endwrench.com/images/pdfs/LoyalInfo.pdf Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now